Godex RT230 Manuale Utente

RT200/RT230 BARCODE PRINTERUSER MANUALUser ManualVersionIssue DateP/N : RT200 series : Rev. 1.3 : 2012.10.25 : 920-014311-00

2 Printer Setup2.2 Loading The Ribbon006A New Ribbon Module Installation1. Attach the ribbon to the empty ribbon core with the adhesive strip

2 Printer Setup0072. Then place the left-hand side of the ribbon.Load The Ribbon On The PrinterFor Ribbon Supply Module1. Place the right-han

2 Printer Setup0083. The ribbon supply module loading is completed.Load The Ribbon On The PrinterFor Ribbon Rewind Module1. Pass the ribbon t

2 Printer Setup0092. Place the right-hand side of empty ribbon core first.Right sidePush the empty ribbon core to tighten the spring of the hold

2 Printer Setup2.3 Loading The Label Roll Module010A New Label Supply Module Loading1. Unlock the release catch to lift the label supply hub.

2 Printer Setup0113. Push the label supply module downward and close the release catch.Push downward to fix the module4. A new label supply m

2 Printer Setup0122Close the printer cover1Push the release catch2. Unlock the release catch to close the printer cover.3. Press the FEED key

2 Printer Setup2.4 Connecting The Printer To The Host Computer0131. Please make sure that the printer is switched off.2. Connect the power

2 Printer Setup0143. Connect the USB/serial cable to the printer and host computer.4. Pressing the power button. The power LED indicator shou

2 Printer Setup2.5 Installing Printer Driver and GoLabel with Super Wizard CD0151. Insert the Super Wizard CD in the CD/DVD drive of the host

ContentsRT200/RT230 USER MANUALCONTENTS1 Barcode Printer 001 1.1 1.2 Box Content Getting To Know Your Printer 001 002 2 Printer Setup 005 2.1 2.2 2.3

2 Printer Setup0164. As the printer driver and GoLabel are installing, a screen will display a progress bar.6. As the optional steps, you can

2 Printer Setup0171. Insert the product CD in the CD/DVD drive of the host computer and open the "Seagull Drivers" folder on the CD.

2 Printer Setup0184. Specify the port used to connect the printer to the host computer.6. Once the installation is complete, a summary of the

2 Printer Setup0197. Once the driver installation is complete, the new printer should appear in the "Printers and Faxes" folder.Godex

3 Printer Setting And Control3.1 Operation Panel020FEED ButtonWhen you press the FEED button, the printer moves the label to the defined stop po

3 Operation Panel3.2 Label Calibration and Self Test021Label CalibrationThe printer can automatically detect and store label height.That means t

3 Operation Panel022Auto Label Calibration ButtonKeep pressing AUTO CALIBRATION button for 1 second, the printer can immediately run the label size

3 Operation Panel3.3 Error Alerts023In the event of a problem that prevents normal functioning of the printer, you will see an error message on

4 NetSetting for Ethernet4.1 Installing The NetSetting software024The NetSetting software is used to manage the network configurations when conn

4 NetSetting for Ethernet4.2 The Interface of NetSetting025Click the NetSetting icon to start the program; you will see the start page as below.

DeclarationRT200/RT230 USER MANUALFCC COMPLIANCE STATEMENTFOR AMERICAN USERSThis equipment has been tested and found to comply with the limits for a C

4 NetSetting for Ethernet026**** To fully benefit from the NetSetting software, you should be familiar with basic networking principles. Please

4 NetSetting for Ethernet027You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.Alert Path SettingNet

4 NetSetting for Ethernet028You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.Alert Message Setting

4 NetSetting for Ethernet029You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values.Printer Configuration

4 NetSetting for Ethernet030You can press “Send Command” button to send printer commands via Ethernet port and control the printer remotely.User Co

4 NetSetting for Ethernet031In addition to the firmware update, you can press “Recover To Factory Settings” button to restore the printer configura

5 Accessories032Before installing the optional modules, please make some preparations as follows.1. Turn off the printer Remember to switc

5 Accessories0334. Remove the platen Lift up the release clips on both sides of the platen to release and pull upward the platen.CLIPRelea

5 Accessories5.2 Installing The Label Dispenser034The Overview Of The Label DispenserPAPER SENSORPAPER FEED ROLLERCOVERCONNECTION CABLE OF LABEL

5 Accessories0352. Place label dispenser to align both holes of screw and then tighten the screws.3. Place the platen back to the printer and

Safety instructionsRT200/RT230 USER MANUALSAFETY INSTRUCTIONSPlease read the following instructions carefully.1. Keep the equipment away from humid

5 Accessories0366. Open the cover on the bottom of printer.7. Plug the connector fo the label dispenser to the jack.8. Close the cover of

5 Accessories0372. Feed the Label stock through the label guides.3. Pull the label liner through the platen and the steel of the label dispen

5 Accessories0384. The feeding path of label and liner should be as shown in below graphic.5. Close the label dispenser and printer cover. Th

5 Accessories0396. Press the FEED button to feed the label. The label will be peeled from the liner while it passes through the label dis

5 Accessories5.3 Installing The Cutter040The Overview Of The Cutter****Remember to switch off the printer before installing the cutter.****Do no

5 Accessories0412. Place the cutter to align both holes of screw and then tighten the screws.3. Place the platen back to the printer and lock

5 Accessories0426. Open the cover on the bottom of printer.7. Plug the connector for the cutter to the jack.8. Close the cover of the modu

5 Accessories0432. Close the top cover and printing mechanism. To finish, press the FEED button to set the label position.****We advise against

6 Maintenance And Adjustment6.1 Cleaning The Print Head044Dirt on the print head or ribbon, or glue residue from the label stock may result in i

6 Maintenance And Adjustment6.2 Troubleshooting045**** If any problems occur that are not described here, please contact your dealer.Problem So

RT200/RT230 Barcode Printer1 Barcode Printer1.1 Box ContentPlease check that all of the following items are included with your printer.001USB C

RT200/RT230 USER MANUAL APPENDIX PRODUCT SPENIFICATIONS Model RT200 RT230 Print Method Thermal Transfer / Direct Thermal Resolution 203 dpi (8

RT200/RT230 USER MANUAL APPENDIX PRODUCT SPENIFICATIONS Model RT200 RT230 Real Time Clock Standard Power Auto Switching 100-240VAC, 50-60Hz Envi

AppendixINTERFACERT200/RT230 USER MANUALAPPENDIXPinout DescriptionConnector Type : Type B Serial PortDefault settings： Baud rate 9600, no parity,

Front View1 Barcode Printer1.2 Getting To Know Your Printer002Device OverviewRear ViewETHERNET PORTSERIAL PORTFAN-FOLD LABEL INSERTFeed slot f

Bottom View1 Barcode Printer003COVER OF THE MODULE CONNECTION JACKS**** Cut-outs are not intended for wall-mount use.

1 Barcode PrinterThe Internal View Of Printer004RELEASE CATCHRelease catch for closing the printer coverTOP COVERLABEL SUPPLY MODULELABEL SENSOR MO

2 Printer Setup2.1 Open The PrinterOpen The Printer Cover And The Printing MechanismPlace the printer on a flat surface. Open the printer cover